Introduction

System can perform object metadata sync with Asset+ server.

Object metadata is synchronized both ways. If conflicts are detected (data was updated on both sides), object must be "merged" by the user. 

Live data view

System supports display of live data from Asset+ in a dedicated property tab.

This is an unmodified, unmapped data that is fetched directly from a remote server.

To enable that view, create a new EID domain and enable "live" feature. Select AssetPlus data connector. 

Open

Open

Object metadata Sync

Auto Sync

When AutoSync is enabled (see configuration), all changes made on objects are synchronized automatically to Asset+ server. 

Synchronization is performed on event, that is imminently after object was modified. Data modified in Asset+ is fetched on time interval set in system settings, e.g. every 5 minutes. 

Manual Sync

Manual sync of objects can be triggered only from Sync Manager. Sync is usually triggered for objects in specific state, e.g. objects that failed sync. 

Sync Status Widget

Sync Manager

Sync Status

Initialize Sync

Initialize sync procedure can be performed by using the Full Sync function

 Attention  - running full sync will reinitialize the sync data and will use "Asset wins" strategy, meaning that data that is different between our system and Asset, will be initialized with values taken from Asset.

If the data is identical, no changes will be made and object swill receive "in sync" status. This procedure can be repeated at any time, but it will always result in "asset data wins" strategy being applied. 

Sync All

Sync all data that is covered by current filter selection. Note, that this is a "forced" check that will do the following:

Make sure that we do not have a newer object in our database that was not synced, but also pull data from Asset and compare with our data. 

If changes are detected, update will be performed. 

Sync Selected

Sync selected has the same logic as Sync All, but is performed only for explicitly selected object. 

Export To Excel

Exports to excel current list of object. 

Merge Process

Objects with status Conflict should be merged. It means that we cannot send local data to Asset without overwriting it. Data has to be merged by the user, deciding what data should become new "master data". 

The result of the merge will be saved both locally and to Asset database. It might be the case, that object was modified outside of mapped / synchronized fields.

System does not detect that and will still indicate the conflict, even thou all fields might seem to have the same values. The object must be merged and saved anyway, but if system does not detect any fields to be updated the actual update will be skipped. 

Object in conflict - a sync will not be performed:

Select Merge function, then use left/right arrow to move properties into a merged object. When done, select Save Merged Data. Data will be written to both systems. 

Configuration

System Settings

Set server type to Asset+ and select domain used for sync and metadata mapping. 

Also enable Autosync and select user that will be used to perform the sync. Please note that this user needs read/write permissions to all objects and fields being synced. 

Properties / settings required by Asset+ are marked in red:

EID Domain Settings

Create a domain that will be used to configure mapping between object classes (categories) between our system and Asset+

Define all categories and their respective properties that you would like to map from Asset+:

Then map them to respective fields in our system:

 Important notes:

• field types must match on both systems, so date must be matched to date, number to number, string to string. 

• There is no need to indicate a GUID/ID field - all objects are always matched by system GUIDS (FM GUID on Asset+ side and MasterGUID in our system)

Authentication settings

Authentication between our system and Asset+ is performed based on Identity Provider configuration. 

For data sync a user indicated in the system settings is used to read the data from our system. A respective user in Asset+ must exists (with the same email address).

Data Access for 3D view and live metadata view is based on currently logged in user. User with the same email address must exists in Asset+.

How to add Identity Provider:

• Go to authentication realm for your application, in Identity providers select Add Provider, select  OpenID Connect client

• Alias, e.g. asset-kc-oidc must be set in system configuration in Asset+ section

• Use a URL to a well known Discovery endpoint

  • https://sso-test.serviceworksglobal.cloud/auth/realms/AssetDB/.well-known/openid-configuration

• make sure to provide valid Client ID and Client Secret

 Note: this Provider is required for the token exchange to work. It is based on Client ID and Client Secret.

It can also, at the same time, be used to perform user login if you would like to achieve an SSO functionality between our system and Asset+.